connect ap to a switch (with your laptop connected) to get an ip address from dual-server.
---------------------------------------------------------------------------------------------------------------------------------------
eth0: port 1(ath0sn0) entering learning state
eth0: topology change detected, propagating
eth0: port 2(oct0) entering forwarding state
eth0: topology change detected, propagating
eth0: port 1(ath0sn0) entering forwarding state <--- At this point is when it gets an IP address from the DHCP server.
---------------------------------------------------------------------------------------------------------------------------------------
I did a quick scan to find the IP address it gave out. Web browse into the AP. Above, after it gets an IP address, go to http://192.168.0.7 . (192.168.0.7 was my address given out by DHCP).
Above, login with admin/admin123 .
Below, go to Firmware Update.
Fill in the info on the screen (Filename, TFTP Server IP Address, TFTP radio) See below.
Make sure TFTP is running on your laptop:
Select "Perform Update" in the AP interface. Once you select that, you get this message below:
Select "Yes". It then logs you out automatically.
It takes the 7131 around 10 minutes or so to upgrade and boot back up. Below is the TFTP (Two screenshots).
Sniff of the TFTP.
TFTP from my laptop.
When it reboots, it goes through this process in CLI on the 7131:
-----------------------------------------------------------------------------------------------------------------------------------------
Status 0
Restarting system.
.
CN3010_EVB_HS5 board revision major:1, minor:0, serial #: 2007-1.0-00179
OCTEON CN3010-SCP revision: 2, Core clock: 500 MHz, DDR clock: 266 MHz (532 Mhz data rate)
DRAM: 128 MB
Rom Based Init Sequence complete
Press the R key within 4 seconds for ROM based Diags
Else, Boot code relocation to DRAM will commence
Commencing Boot code relocation to DRAM
Flash: 8 MB
NAND: 512 MiB
Clearing DRAM...... done
BIST check passed.
Starting PCI
PCI Status: PCI 32-bit
PCI BAR 0: 0x00000000, PCI BAR 1: Memory 0x00000000 PCI 0xf8000000
Net: octeth0, octeth1
BR71xx Boot Firmware Version 3.2.2.0-011R, CPLD Revision 3.19
Copyright(c) 2009. All rights reserved.
Press escape key to run boot firmware .............
NAND read: device 0 offset 0x8000000, size 0x20c2000
Reading data from 0x8000000 -- 0% complete.Reading data from 0x8053800 -- 1% complete.Reading data from 0x80a7800 -- 2% complete.Reading data from 0x80fb800 -- 3% complete.Reading data from 0x814f000 -- 4% complete.Reading data from 0x81a3000 -- 5% complete.Reading data from 0x81f7000 -- 6% complete.Reading data from 0x824b000 -- 7% complete.Reading data from 0x829e800 -- 8% complete.Reading data from 0x82f2800 -- 9% complete.Reading data from 0x8346800 -- 10% complete.Reading data from 0x839a000 -- 11% complete.Reading data from 0x83ee000 -- 12% complete.Reading data from 0x8442000 -- 13% complete.Reading data from 0x8496000 -- 14% complete.Reading data from 0x84e9800 -- 15% complete.Reading data from 0x853d800 -- 16% complete.Reading data from 0x8591800 -- 17% complete.Reading data from 0x85e5000 -- 18% complete.Reading data from 0x8639000 -- 19% complete.Reading data from 0x868d000 -- 20% complete.Reading data from 0x86e1000 -- 21% complete.Reading data from 0x8734800 -- 22% complete.Reading data from 0x8788800 -- 23% complete.Reading data from 0x87dc800 -- 24% complete.Reading data from 0x8830000 -- 25% complete.Reading data from 0x8884000 -- 26% complete.Reading data from 0x88d8000 -- 27% complete.Reading data from 0x892c000 -- 28% complete.Reading data from 0x897f800 -- 29% complete.Reading data from 0x89d3800 -- 30% complete.Reading data from 0x8a27800 -- 31% complete.Reading data from 0x8a7b800 -- 32% complete.Reading data from 0x8acf000 -- 33% complete.Reading data from 0x8b23000 -- 34% complete.Reading data from 0x8b77000 -- 35% complete.Reading data from 0x8bca800 -- 36% complete.Reading data from 0x8c1e800 -- 37% complete.Reading data from 0x8c72800 -- 38% complete.Reading data from 0x8cc6800 -- 39% complete.Reading data from 0x8d1a000 -- 40% complete.Reading data from 0x8d6e000 -- 41% complete.Reading data from 0x8dc2000 -- 42% complete.Reading data from 0x8e15800 -- 43% complete.Reading data from 0x8e69800 -- 44% complete.Reading data from 0x8ebd800 -- 45% complete.Reading data from 0x8f11800 -- 46% complete.Reading data from 0x8f65000 -- 47% complete.Reading data from 0x8fb9000 -- 48% complete.Reading data from 0x900d000 -- 49% complete.Reading data from 0x9060800 -- 50% complete.Reading data from 0x90b4800 -- 51% complete.Reading data from 0x9108800 -- 52% complete.Reading data from 0x915c800 -- 53% complete.Reading data from 0x91b0000 -- 54% complete.Reading data from 0x9204000 -- 55% complete.Reading data from 0x9258000 -- 56% complete.Reading data from 0x92ac000 -- 57% complete.Reading data from 0x92ff800 -- 58% complete.Reading data from 0x9353800 -- 59% complete.Reading data from 0x93a7800 -- 60% complete.Reading data from 0x93fb000 -- 61% complete.Reading data from 0x944f000 -- 62% complete.Reading data from 0x94a3000 -- 63% complete.Reading data from 0x94f7000 -- 64% complete.Reading data from 0x954a800 -- 65% complete.Reading data from 0x959e800 -- 66% complete.Reading data from 0x95f2800 -- 67% complete.Reading data from 0x9646000 -- 68% complete.Reading data from 0x969a000 -- 69% complete.Reading data from 0x96ee000 -- 70% complete.Reading data from 0x9742000 -- 71% complete.Reading data from 0x9795800 -- 72% complete.Reading data from 0x97e9800 -- 73% complete.Reading data from 0x983d800 -- 74% complete.Reading data from 0x9891000 -- 75% complete.Reading data from 0x98e5000 -- 76% complete.Reading data from 0x9939000 -- 77% complete.Reading data from 0x998d000 -- 78% complete.Reading data from 0x99e0800 -- 79% complete.Reading data from 0x9a34800 -- 80% complete.Reading data from 0x9a88800 -- 81% complete.Reading data from 0x9adc800 -- 82% complete.Reading data from 0x9b30000 -- 83% complete.Reading data from 0x9b84000 -- 84% complete.Reading data from 0x9bd8000 -- 85% complete.Reading data from 0x9c2b800 -- 86% complete.Reading data from 0x9c7f800 -- 87% complete.Reading data from 0x9cd3800 -- 88% complete.Reading data from 0x9d27800 -- 89% complete.Reading data from 0x9d7b000 -- 90% complete.Reading data from 0x9dcf000 -- 91% complete.Reading data from 0x9e23000 -- 92% complete.Reading data from 0x9e76800 -- 93% complete.Reading data from 0x9eca800 -- 94% complete.Reading data from 0x9f1e800 -- 95% complete.Reading data from 0x9f72800 -- 96% complete.Reading data from 0x9fc6000 -- 97% complete.Reading data from 0xa01a000 -- 98% complete.Reading data from 0xa06e000 -- 99% complete.Reading data from 0xa0c1800 -- 100% complete.
34349056 bytes read: OK
>>>> Entering Critical Programming Phase DO NOT POWER OFF UNIT! <<<<
Un-Protect Flash Bank # 1
................................ done
NAND erase: device 0 whole chip
Erasing at 0x0 -- 0% complete.Erasing at 0x500000 -- 1% complete.Erasing at 0xa20000 -- 2% complete.Erasing at 0xf40000 -- 3% complete.Erasing at 0x1460000 -- 4% complete.Erasing at 0x1980000 -- 5% complete.Erasing at 0x1ea0000 -- 6% complete.Erasing at 0x23c0000 -- 7% complete.Erasing at 0x28e0000 -- 8% complete.Erasing at 0x2e00000 -- 9% complete.Erasing at 0x3320000 -- 10% complete.Erasing at 0x3840000 -- 11% complete.Erasing at 0x3d60000 -- 12% complete.Erasing at 0x4280000 -- 13% complete.Erasing at 0x47a0000 -- 14% complete.Erasing at 0x4cc0000 -- 15% complete.Erasing at 0x51e0000 -- 16% complete.Erasing at 0x5700000 -- 17% complete.Erasing at 0x5c20000 -- 18% complete.Erasing at 0x6140000 -- 19% complete.Erasing at 0x6660000 -- 20% complete.Erasing at 0x6b80000 -- 21% complete.Erasing at 0x70a0000 -- 22% complete.Erasing at 0x75c0000 -- 23% complete.Erasing at 0x7ae0000 -- 24% complete.Erasing at 0x7fe0000 -- 25% complete.Erasing at 0x8500000 -- 26% complete.Erasing at 0x8a20000 -- 27% complete.Erasing at 0x8f40000 -- 28% complete.Erasing at 0x9460000 -- 29% complete.Erasing at 0x9980000 -- 30% complete.Erasing at 0x9ea0000 -- 31% complete.Erasing at 0xa3c0000 -- 32% complete.Erasing at 0xa8e0000 -- 33% complete.Erasing at 0xae00000 -- 34% complete.Erasing at 0xb320000 -- 35% complete.Erasing at 0xb840000 -- 36% complete.Erasing at 0xbd60000 -- 37% complete.Erasing at 0xc280000 -- 38% complete.Erasing at 0xc7a0000 -- 39% complete.Erasing at 0xccc0000 -- 40% complete.Erasing at 0xd1e0000 -- 41% complete.Erasing at 0xd700000 -- 42% complete.Erasing at 0xdc20000 -- 43% complete.Erasing at 0xe140000 -- 44% complete.Erasing at 0xe660000 -- 45% complete.Erasing at 0xeb80000 -- 46% complete.Erasing at 0xf0a0000 -- 47% complete.Erasing at 0xf5c0000 -- 48% complete.Erasing at 0xfae0000 -- 49% complete.Erasing at 0xffe0000 -- 50% complete.Erasing at 0x10500000 -- 51% complete.Erasing at 0x10a20000 -- 52% complete.Erasing at 0x10f40000 -- 53% complete.Erasing at 0x11460000 -- 54% complete.Erasing at 0x11980000 -- 55% complete.Erasing at 0x11ea0000 -- 56% complete.Erasing at 0x123c0000 -- 57% complete.Erasing at 0x128e0000 -- 58% complete.Erasing at 0x12e00000 -- 59% complete.Erasing at 0x13320000 -- 60% complete.Erasing at 0x13840000 -- 61% complete.Erasing at 0x13d60000 -- 62% complete.Erasing at 0x14280000 -- 63% complete.Erasing at 0x147a0000 -- 64% complete.Erasing at 0x14cc0000 -- 65% complete.Erasing at 0x151e0000 -- 66% complete.Erasing at 0x15700000 -- 67% complete.Erasing at 0x15c20000 -- 68% complete.Erasing at 0x16140000 -- 69% complete.Erasing at 0x16660000 -- 70% complete.Erasing at 0x16b80000 -- 71% complete.Erasing at 0x170a0000 -- 72% complete.Erasing at 0x175c0000 -- 73% complete.Erasing at 0x17ae0000 -- 74% complete.Erasing at 0x17fe0000 -- 75% complete.Erasing at 0x18500000 -- 76% complete.Erasing at 0x18a20000 -- 77% complete.Erasing at 0x18f40000 -- 78% complete.Erasing at 0x19460000 -- 79% complete.Erasing at 0x19980000 -- 80% complete.Erasing at 0x19ea0000 -- 81% complete.Erasing at 0x1a3c0000 -- 82% complete.Erasing at 0x1a8e0000 -- 83% complete.Erasing at 0x1ae00000 -- 84% complete.Erasing at 0x1b320000 -- 85% complete.Erasing at 0x1b840000 -- 86% complete.Erasing at 0x1bd60000 -- 87% complete.Erasing at 0x1c280000 -- 88% complete.Erasing at 0x1c7a0000 -- 89% complete.Erasing at 0x1ccc0000 -- 90% complete.Erasing at 0x1d1e0000 -- 91% complete.Erasing at 0x1d700000 -- 92% complete.Erasing at 0x1dc20000 -- 93% complete.Erasing at 0x1e140000 -- 94% complete.Erasing at 0x1e660000 -- 95% complete.Erasing at 0x1eb80000 -- 96% complete.Erasing at 0x1f0a0000 -- 97% complete.Erasing at 0x1f5c0000 -- 98% complete.Erasing at 0x1fae0000 -- 99% complete.Erasing at 0x1ffe0000 -- 100% complete.
OK
>>>> Updating Nor Bootstrap <<<<
Copy to Flash... done
>>>> Updating Boot OS <<<<
Copy to Flash... ................done
Copy to Flash... ................done
>>>> Updating Kernels <<<<
NAND write: device 0 offset 0x220000, size 0x260800
>>>> Verifying Firmware Update <<<<
Updating Nor Bootstrap : PASSED
Updating Bootloader : PASSED
Updating Kernel : PASSED
Updating File System : PASSED
Updating Unamed Block : PASSED
BootOS Copyright (c) 2004-2011. All rights reserved.
boot image at 0x00220000..good
data bus walking 1's......pass
address bus walking 1's...pass
ddr device test...........pass
clearing ram..............done
copying to ram............done
BootOS Copyright (c) 2004-2011. All rights reserved.
BR71XX version 5.2.0.0-069R
warning: invalid partition table magic number
initialized partition table
initializing pci
achip:pcc:0x000000ff,prc:0x00000020,fc:0x00000000
pci init done
fpga_sensor_mode 255
hw_type=0, sku=0x0, ps_status=0xae, pwr_mgmt=0xff, radio_cfg=0xff, per_reset_ctrl=0x20
loading linux image 2
...................
Welcome.
restoring /etc2/./ppp
restoring /etc2/./nvram
restoring /etc2/./raddb
restoring /etc2/./stunnel
restoring /etc2/./stunnel/certs
restoring /etc2/./stunnel/private
restoring /etc2/./CertMgr
restoring /etc2/./CertMgr/keys
restoring /etc2/./CertMgr/certs
restoring /etc2/./CertMgr/tmp_keys
restoring /etc2/./CertMgr/tmp_certs
restoring /etc2/./snmpEngine
restoring /etc2/./ppp/hsdpa_apn_set
restoring /etc2/./stunnel/current
restoring /etc2/./imish-passwd
restoring /etc2/./log.conf
restoring /etc2/./smtpnot.conf
restoring /etc2/./system_env_vars
restoring /etc2/./env_vars
restoring /etc2/./nvram/startup-config
restoring /var2/./lib
restoring /var2/./lib/dpd
restoring /var2/./lib/dhcp
restoring /var2/./log
restoring /var2/./run
restoring /var2/./tmp
restoring /var2/./state
restoring /var2/./state/dhcp
restoring /var2/./history
restoring /var2/./run/utmp
restoring /flash/./log
restoring /flash/./cache
restoring /flash/./crashinfo
restoring /flash/./hotspot
restoring /flash/./hotspot/lib
restoring /flash/./hotspot/cgi-bin
restoring /flash/./floorplans
This can take some time, please be patient.
Sat Jan 1 00:00:00 UTC 2011
Converting APN 4.x configuration information to 5.x format
Starting daemons...
......
Running Secondary software, version 5.2.0.0-069R
Alternate software Primary, version 5.2.0.0-069R
Software fallback feature is enabled
Please press Enter to activate this console.
br7131-F23460 login:
---------------------------------------------------------------------------------------------------------------------------------------
After the AP upgrades, web browse into it via HTTPS. https://192.168.0.7
Upgrade complete.
No comments:
Post a Comment
Your comment will be reviewed for approval. Thank you for submitting your comments.